1.948,10€ (VAT included)
Grundfos SQFlex are submersible drilling pumps designed to pump
water Water supply systems based on renewable energy.
Graphic of Culva Grundfos Pump
Dry run protection
The SQF pump is protected against dry running to
to avoid damage to the pump. dry running
The protection is activated by a water level electrode placed
on the motor cable 0,3 – 0,6 m above the pump,
depending on the type of pump.
The water level electrode measures the contact
Engine sleeve resistance through water. When
the water level drops below the water level electrode, the
the pump will be cut off. The pump will turn on automatically
again 5 minutes after the water level is above water
level electrode
Fig. 2 Vertical installation
Fig. 3 Horizontal installation
High efficiency
The MSF 3 motor is a permanent magnet motor
(PM motor) with greater efficiency within the
power range compared to a conventional asynchronous
engine.
In addition to this, the segmented motor stator
contributes considerably to high efficiency.
The MSF 3 engine is further characterized by
High locked rotor torque even with low power supply.
Overvoltage and undervoltage
protection
Overvoltages and undervoltages may occur in case of
unstable power supply or faulty installation.
The pump will shut down if the voltage drops outside the
allowable voltage range. The motor is automatically
cut off when the voltage is back within the allowable
voltage range. Therefore, no additional protection relay is needed.
necessary.
Note: The MSF 3 motor is transient protected
of the power supply according to EN/IEC 61000-4-5
(6 kV). In areas with high lightning intensity, external
Lightning protection is recommended.
Overload protection
In case the upper load limit is exceeded, the motor
automatically compensate for this by reducing the
speed. If the speed drops below 500 min-1, the motor
be cut off automatically.
The engine will remain off for 10 seconds, after which
period, the pump will attempt to restart automatically.
Overload protection prevents the motor from burning out.
Overtemperature protection
A permanent magnet motor emits very little heat to
its surroundings. In combination with an efficient
internal circulation system that removes heat from
the rotor, stator and bearings, this fact ensures
optimal engine operating conditions.
As additional protection, the electronic unit has a
temperature sensor. When the temperature rises above
+85 °C, the engine switches off automatically. When the
temperature has dropped to +75 °C, the engine is
it automatically cuts off again.
Maximum power point
(MPPT)
The built-in electronic unit gives the SQFlex system
a series of advantages compared to conventional
products One of these advantages is the integrated function
microprocessor with MPPT (MPPT = Maximum Power
point tracking).
Thanks to the MPPT function, the working point of the pump is
continuously optimized according to input power
available. MPPT is only available for connected pumps
to the DC supply.
Wide voltage range
The wide voltage range allows the motor to run at
any voltage from 30-300 VDC or 90-240 VAC. This
makes installation and sizing especially easy.
Reliability
The MSF 3 engine has been developed in order to
high reliability which is achieved through the following
characteristics:
• carbon/ceramic bearings
• excellent starting capabilities
• various protection facilities.
Installation
The following features ensure easy installation of the
SQF pump:
• Reduced weight that guarantees easy handling.
• Installation in 3″, 4″ or larger wells.
• Only one on/off switch is needed, which means
No additional motor starter/starter box needed.
• SQF is available with cable and plug.
Note: Horizontal installation requires water level
electrode to be placed min. 0,3 to 0,6 m above the
pump to ensure protection against dry running.
Buy Plus Energy submersible solar pump
Buy the Plus Energy submersible solar pump It is fast, safe and comfortable thanks to Wccsolar, and the Plus Energy submersible solar pump has an official Wccsolar guarantee.
Contact us to receive more information.
Models
Exclusive
– The manufacturing material of the engine and the body of the
pump is AISI 304 stainless steel.
– Three 3-wire wiring: (Earth + Pole 1 + Pole 2) Without
Defined polarity for easy installation.
– 2HP motor
- Centrifugal pump.
– StopFlow pump protection system
FEATURES OF THE UControl-250x CONTROLLER:
• Possibility of manual or automatic configuration.
• Automation of tank filling.
• Direct irrigation automation.
• Possibility of using a generating set or photovoltaic panels.
• LED indicators for full or empty tank.
• Weather resistant (avoiding direct sunlight).
Frequency: 50 60-Hz
Power: 60VDC-300VDC
AC range: 90-240V
